PAKSAT MM1 38.2°E Frequencies & Transponder List 2026

Latest PAKSAT MM1 38.2°E Frequencies & Transponder List 2026

Updated PAKSAT MM1 satellite frequencies, C-band transponders, symbol rates, receiver settings and manual scanning guide.

UPDATED: SEPTEMBER 2026

📢 Important Frequency Update
PAKSAT MM1 transponder parameters, channel lineups and transmission details can change over time. Always verify the current TP information before updating your receiver.

FEATURED IMAGE

PAKSAT MM1 38.2°E satellite frequency and transponder guide 2026.

PAKSAT MM1 is positioned at 38.2° East and provides satellite communication services through C, Ku, Ka and L-band payloads. PAKSAT International lists television broadcasting, broadband, mobile backhaul and VSAT connectivity among its services.

This guide focuses on selected PAKSAT MM1 C-band frequencies, symbol rates, DVB standards, modulation and FEC settings that can be used for receiver setup, signal testing and channel scanning.

🎯 Quick Setup Tip:
When checking dish alignment, pay more attention to Signal Quality and transponder lock than to Signal Strength alone. A receiver can show signal strength even when the selected transponder is not correctly locked.

🛰️ PAKSAT MM1 Satellite Position & Technical Details

📍 Orbital Position

38.2° East

📡 C-Band

Used for several television and communication transmissions.

📺 Main Services

TV Broadcasting, Broadband, Mobile Backhaul and VSAT.

🌐 Supported Payloads

C, Ku, Ka and L Bands

According to PAKSAT International, PAKSAT-MM1 operates at 38.2°E and supports C, Ku and Ka communication payloads plus L-band SBAS services.

📋 Latest PAKSAT MM1 C-Band Frequencies 2026

The table below contains selected current PAKSAT MM1 C-band transponders that are useful for receiver setup and reception testing. It is intentionally presented as a selected TP list, not as a claim that these are the only active transponders on the satellite.

Frequency	Polarity	Symbol Rate	System / Modulation	FEC	Example Service
3707 MHz	H	1200	DVB-S	3/4	Radio Pakistan
3722 MHz	H	3200	DVB-S2 / 8PSK	3/5	ABN News
3725 MHz	H	3000	DVB-S2 / 8PSK	3/4	Sun News
3870 MHz	H	13333	DVB-S2 / 8PSK	3/4	PTV Network
3975 MHz	H	9600	DVB-S2 / 8PSK	3/4	Express Network
4021 MHz	H	6800	DVB-S2 / 8PSK	3/4	Aan TV / M Network
4099 MHz	H	3200	DVB-S2 / 8PSK	3/4	LTN Family / Filmazia / Aruj TV

Note: Channel availability can vary by time and transmission status. Always perform a fresh scan when a listed service is not found.

⭐ Recommended Reception Check:
3870 H 13333 is a useful current reference transponder. Current listings identify it as C-band DVB-S2/8PSK with SR 13333 and FEC 3/4, carrying multiple PTV services.

FREQUENCY TABLE SCREENSHOT

PAKSAT MM1 38.2°E C-band frequency and transponder reference table.

📡 PAKSAT MM1 3870 H 13333 Settings

The 3870 H 13333 transponder is one of the useful reference frequencies for checking PAKSAT MM1 reception. Current LyngSat data identifies it as a C-band DVB-S2 / 8PSK transmission with FEC 3/4.

Satellite: PAKSAT MM1 Orbital Position: 38.2°E Frequency: 3870 MHz Polarity: Horizontal (H) Symbol Rate: 13333 System: DVB-S2 Modulation: 8PSK FEC: 3/4

Current listings show PTV Home, PTV News, PTV Global, PTV Sports, Pakistan TV and radio services on this transponder.

RECEIVER SETTINGS SCREENSHOT

Example receiver settings for PAKSAT MM1 3870 H 13333.

🎯 PAKSAT MM1 3975 H 9600

Another current PAKSAT MM1 C-band reference is 3975 H 9600. Current LyngSat data lists it as DVB-S2 / 8PSK, SR 9600 and FEC 3/4.

Satellite: PAKSAT MM1 Orbital Position: 38.2°E Frequency: 3975 MHz Polarity: Horizontal (H) Symbol Rate: 9600 System: DVB-S2 Modulation: 8PSK FEC: 3/4

Current listings associate this transponder with services including Express News, Express Entertainment, Chaupal HD and Express 24/7.

📺 PAKSAT MM1 4021 H 6800

The 4021 H 6800 transponder is also currently listed on PAKSAT MM1 C-band as DVB-S2 / 8PSK with FEC 3/4.

Satellite: PAKSAT MM1 Frequency: 4021 MHz Polarity: Horizontal (H) Symbol Rate: 6800 System: DVB-S2 Modulation: 8PSK FEC: 3/4

Current listings show services including Aan TV, M News, M World, M Sports, M Entertainment and Planet 6 on this transponder.

🛠️ How to Scan PAKSAT MM1 38.2°E

1

Open Installation Menu
Go to your receiver's Menu → Installation → Satellite Setup. Menu names can differ by receiver model.

2

Select PAKSAT MM1
Select the satellite position around 38.2°E or create the satellite entry if it is not already present.

3

Configure the C-Band LNB
Enter the correct LNB type, LO frequency, DiSEqC port and other settings according to your actual dish and receiver installation.

4

Add a Known TP
Enter 3870 H 13333 as a reception-checking reference and monitor Signal Quality.

5

Run Manual Scan
Use Manual TP Scan when you already know the exact frequency and symbol rate you want to search.

6

Run Blind Scan
After confirming dish alignment and LNB settings, Blind Scan can be used to search for additional available transponders.

⚙️ Manual Scan Settings Example

PAKSAT MM1 3870 H 13333:

Satellite: PAKSAT MM1 Position: 38.2°E Frequency: 3870 MHz Polarity: H Symbol Rate: 13333 System: DVB-S2 Modulation: 8PSK FEC: 3/4

If your receiver does not provide an explicit modulation or FEC field, use the receiver's automatic/default option where appropriate and confirm whether the transponder locks successfully.

🔧 PAKSAT MM1 No Signal? Troubleshooting Guide

🎯 Check Dish Alignment

Fine-tune the dish while watching Signal Quality. Even a small alignment error can prevent a weak transponder from locking.

📡 Check LNB Settings

Verify the correct C-band LNB type, LO configuration, DiSEqC port, polarization and cable connections.

🔢 Check Frequency & SR

Enter the frequency and symbol rate exactly. For example, 13333 is different from 1333.

📶 Test Another TP

If one frequency does not lock, test another currently active PAKSAT MM1 transponder.

✅ Quick No-Signal Checklist

• Confirm the satellite is set around 38.2°E.
• Confirm you are using the correct C-band LNB setup.
• Check the DiSEqC port if a switch is installed.
• Check coaxial cable and connector condition.
• Enter frequency, polarity and symbol rate correctly.
• Check DVB-S/DVB-S2 and modulation compatibility where required.
• Fine-tune the dish for maximum Signal Quality.
• Try another known active transponder.

🔄 Manual Scan vs Blind Scan

Scan Type	Best For	Main Advantage
Manual TP Scan	Known frequency	Fast and targeted
Blind Scan	Finding available transponders	Searches the receiver's available frequency range
Network Scan	Network-supported services	Can discover additional services when network information is available

📷 PAKSAT MM1 Image & Screenshot SEO

For better SEO and user experience, every image should be relevant to the section where it appears. Avoid using the same ALT text for multiple images.

🖼️ Featured Image

Filename:
paksat-mm1-38-2e-frequency-transponder-list-2026.webp

ALT:
Latest PAKSAT MM1 38.2E satellite frequencies and transponder list 2026

📋 Frequency Screenshot

Filename:
paksat-mm1-c-band-frequency-transponder-2026.webp

ALT:
PAKSAT MM1 38.2E C-band frequencies and transponder table 2026

⚙️ Receiver Screenshot

Filename:
paksat-mm1-3870-h-13333-receiver-settings.webp

ALT:
PAKSAT MM1 3870 H 13333 DVB-S2 8PSK receiver settings

📡 Dish Image

Recommended ALT:
C-band satellite dish aligned for PAKSAT MM1 38.2E reception

📈 Image SEO Best Practice
Use descriptive filenames, unique ALT text, relevant captions and properly sized images. Do not stuff the ALT attribute with repeated keywords.

❓ Frequently Asked Questions

What is the PAKSAT MM1 orbital position?

PAKSAT MM1 is positioned at 38.2° East.

Which frequency can I use to check PAKSAT MM1 reception?

3870 H 13333 is a useful current reference transponder and is listed as DVB-S2/8PSK with FEC 3/4.

What is the PAKSAT MM1 3725 H setting?

The current listing shows 3725 H, SR 3000, DVB-S2/8PSK, FEC 3/4, with Sun News listed on the transponder.

What is the PAKSAT MM1 3975 H setting?

The current listing shows 3975 H, SR 9600, DVB-S2/8PSK, FEC 3/4, with Express services listed on the transponder.

Why does my PAKSAT MM1 frequency show no signal?

Check dish alignment, C-band LNB settings, cable connections, frequency, polarity, symbol rate, receiver compatibility and transponder activity. Then test another known active TP.

Should I use Manual Scan or Blind Scan?

Use Manual Scan when you already know the TP parameters. Use Blind Scan when you want the receiver to search for additional available transponders.

📌 Why PAKSAT MM1 Frequencies Can Change

Satellite transmission parameters can change because channels may migrate, services may be added or removed, networks may be reorganized, or transmission configurations may be updated.

For this reason, an old receiver channel list may not always contain the latest services. If a channel disappears, check the current transponder information and perform a fresh scan.

⚠️ Important:
Do not assume that an old frequency will remain active permanently. Satellite parameters should be verified before making receiver or dish configuration changes.

🔗 Related Satellite Updates

Latest BISS Keys PowerVU Keys Tandberg Keys Satellite Frequencies Receiver Software Satellite Guides PAKSAT Updates

📚 Official & Reference Sources

PAKSAT International:
PAKSAT-MM1 Official Technical Information

LyngSat:
PAKSAT MM1 38.2°E Current Frequency Listing

DishTuner:
PAKSAT MM1 Channels, Frequencies and Coverage

🏁 Final Words

PAKSAT MM1 38.2°E is an important satellite platform for Pakistani and regional satellite users. Its C-band transponders carry a variety of television and radio services, while the satellite also supports wider communication applications.

For receiver setup, first confirm your dish and LNB configuration, then enter a known current transponder such as 3870 H 13333. Check Signal Quality and transponder lock before starting a Manual Scan or Blind Scan.

Because satellite parameters can change, this page should be updated whenever important frequency, symbol-rate, FEC or channel changes are confirmed.

For more BISS Key, PowerVU, Tandberg, satellite frequency, transponder, IPTV and receiver software updates, keep visiting 1BissKey.

⚠️ Disclaimer

Satellite frequencies, channel names, symbol rates, FEC values and transmission details may change without notice. This article is provided for informational and educational purposes. Always verify current parameters before changing receiver, LNB or dish settings.